Identify the 34.5 kV nameplate rating
The 34.5 kV figure may describe one side of a transformer, not its entire voltage configuration. Record the high-side and low-side ratings, the number of phases and the capacity exactly as shown on the nameplate or in an existing equipment record. If the meaning of a value is uncertain, share the source and say so.
For a transformer with this voltage on a nameplate, the complete winding, insulation and accessory information can matter to review. The voltage figure alone is not enough to specify the unit or its removal. A rating is not proof of present operating condition, ownership or electrical compatibility with another system.
Prepare a complete purchase request
Include the site location, whether the unit is connected or stored, and known manufacturer, model and serial number. Multiple tap settings, winding configurations or listed ratings should be included when available rather than condensed into a single voltage.
We consider transformers across all voltage classes, but an offer is not automatic. Do not open an enclosure or measure electrical values for the request. Qualified personnel isolate and disconnect the equipment using the applicable procedures before any authorized removal.
Measure the route, not just the transformer
A useful freight description follows the equipment from its present position to the place a truck could load. Note the narrowest doorway, gate or aisle; any overhead obstruction; and the surfaces that lifting or rolling equipment would have to cross. If the unit sits inside a building, include the room location and whether other equipment blocks the proposed path.
Provide measurements only when they can be obtained safely. A clear route on a drawing is not a guarantee that the unit will fit: allow the transport and rigging parties to assess the actual load, packaging and clearances. Mention stairs, ramps or a freight elevator if they are part of the route, without assuming that they can support the load.
Explain insulating-fluid information
If a unit contains insulating liquid, share any existing fluid identification, labels, maintenance history and environmental records. If the type or PCB status is unknown, say that plainly. Some older electrical equipment may contain PCBs; an appearance, age or manufacturer name by itself does not establish the contents of a particular transformer.
The seller is not asked to perform testing to request an offer. Existing documentation may nevertheless be needed for review and for responsible handling, and an unknown or unsuitable status can affect whether a transaction is possible. Do not drain, sample or disturb the unit merely to prepare an inquiry.
Distinguish a spare from a disconnected unit
A spare transformer may be in storage or it may still be connected as part of a site's contingency plan. A decommissioned unit may be physically disconnected, or the project may still be awaiting qualified electrical work. Describe what is known rather than treating these categories as interchangeable.
If a unit must remain available for backup service, explain that constraint before discussing collection. Site operators should decide when it can be released. The buyer can review available specifications first, while an actual pickup remains subject to safe access and agreed terms.
Confirm who can authorize a sale
The person arranging a project is not always the owner of every electrical asset. Before negotiating, check whether the transformer belongs to the facility, a tenant, a utility or another party, and identify who can sign for it. A contractor managing a shutdown should make its authority and the owner's approval clear.
If the equipment was leased, financed or included in a sale of a building, resolve any restrictions before promising clear ownership. For a lot with several units, prepare an asset list so that the agreement describes exactly what the authorized seller is transferring and what remains on site.
Give a precise pickup description
A city or county name starts the conversation but does not identify a pickup point. Provide the actual site location privately, plus an authorized contact and a description of where the transformer sits within the property. If the mailing address and physical entrance differ, tell the carrier which entrance is intended.
A location that lies near a municipal or county boundary can be described by street address and site entrance rather than relying on a city name alone. Do not publish sensitive access details unnecessarily; the goal is to make a later freight plan workable, not expose facility security information.
How the purchase process works
Start with the unit's location, quantity and any nameplate or inventory details you can share safely. We buy used, surplus and decommissioned transformers across all voltage classes, subject to review and agreed terms. We are a purchaser seeking equipment, not a seller of transformers. A request for review does not guarantee an offer or acceptance of a particular unit.
For equipment accepted under mutually agreed terms, we offer cash, payment upfront and covered freight. Ask for the payment timing, transport scope and any preparation responsibilities in writing before agreeing. Site-specific electrical work, specialized rigging and other arrangements should be spelled out; coverage is subject to the agreed transaction terms.
We do not require sellers to test equipment. Share any existing documents honestly, including known fluid or environmental information. Our review may depend on available documentation, and appropriate legal and safety requirements still apply.
Keep electrical safety separate from the sale
Do not open energized equipment, remove covers, touch connections or attempt electrical work to prepare a listing. Qualified electrical personnel must isolate and disconnect equipment and verify a safe condition using the site's applicable procedures. Treat a unit as potentially energized until the responsible qualified personnel have established otherwise.
Tell the buyer what is known about the equipment and access without attempting unsafe inspection. For possible fluid or PCB concerns, use existing labels and records and involve the appropriate environmental professionals. Do not drain or sample a unit simply to obtain a quote.
Frequently asked questions
Is 34.5 kV enough information for an offer?
It is a useful starting point, but it describes only one part of the specification. Share the other winding voltage, phase, kVA, site location and available records. Review and acceptance depend on the actual equipment and terms.
Do I have to test the transformer before asking for an offer?
No. We do not require sellers to test equipment. Provide existing nameplate information, photographs and records when safely available, and identify unknowns. Review, acceptance and any required documentation depend on the equipment and agreed terms; this does not remove safety or environmental obligations.
Is freight covered and when is payment made?
For a purchase accepted on agreed terms, the business offers payment upfront and covers freight. Confirm the payment and pickup arrangements in the written agreement, including whether specialized rigging, loading or site preparation is separately assigned. An inquiry alone does not guarantee a purchase.
What equipment can I submit for review?
We review used, surplus and decommissioned transformers across all voltage classes, including 34.5 kV rated transformers. Send the quantity, known ratings, location, ownership status and any available records. The final decision and transaction scope depend on review; not every unit can be accepted.
